Volvo Trucks North America (Volvo Trucks) is recalling certain 2024-2025 VNL and VNR vehicles. The steering gear sector shaft may have been improperly heat-treated, which can cause the gear teeth to crack or fracture.
Safety Risk
A fractured steering gear shaft can cause a loss of steering control, increasing the risk of a crash.
Remedy
Dealers will inspect the serial numbers, and replace the steering gears, as necessary, free of charge. Owner notification letters were mailed March 5, 2024. Owners may contact Volvo Trucks customer service at 1-800-528-6586. Volvo Truck's number for this recall is RVXX2401.
Nissan North America, Inc. (Nissan) is recalling certain 2017 Infiniti QX30 vehicles. The steering shaft bore hole for the universal joint bearing may allow excessive movement that, over time, could result in the separation of the bearing and universal joint.
Safety Risk
A separated universal joint bearing can cause a loss of steering control and increase the risk of a crash.
Remedy
Dealers will replace the lower steering shaft, free of charge. Owner notification letters were mailed on July 30, 2021. Owners may contact Nissan customer service at 1-800-867-7669. Nissan's number for this recall is PG1CF.
Daimler Vans USA, LLC (Daimler Vans) is recalling certain 2019 Mercedes-Benz Sprinter VS30 vehicles. The steering shaft that connects to the steering gear may disconnect without warning.
Safety Risk
The steering shaft disconnecting from the steering gear can cause a sudden loss of steering control, increasing risk of a crash.
Remedy
Daimler Vans will notify owners, advising them to stop driving the vehicle immediately. Dealers will inspect the bolts connecting the steering shaft to the steering gear, fully tightening and/or adjusting them, as necessary, free of charge. The recall began February 15, 2019. Owners may contact Daimler Van's customer service at 1-800-367-6372. Daimler Van's number for this recall is 2019010006.
Toyota is recalling certain model year 2004-2009 Prius vehicles manufactured August 5, 2003, through March 30, 2009. The affected vehicles have a steering intermediate extension shaft assembly built with metal splines that complete the connection from the steering wheel to the steering gear. These splines may have been manufactured with an insufficient hardness.
Safety Risk
Over time, the splines may wear and eventually fail resulting in a loss of steering ability, increasing the risk of a vehicle crash.
Remedy
Toyota will notify owners, and dealers will inspect the extension shaft and replace it if it is one with insufficient hardness, free of charge. The recall began during December 2012. Owners may contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331.
GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2011 CHEVROLET CRUZE VEHICLES MANUFACTURED FROM OCTOBER 2, 2009, THROUGH APRIL 21, 2011. THE BOLT ATTACHING THE INTERMEDIATE STEERING SHAFT TO THE STEERING GEAR INPUT SHAFT MAY NOT HAVE BEEN PROPERLY INSTALLED.
Safety Risk
THIS COULD ALLOW THE SHAFTS TO SEPARATE, RESULTING IN THE LOSS OF STEERING. LOSS OF STEERING CONTROL MAY INCREASE THE RISK OF A CRASH.
Remedy
DEALERS WILL INSPECT, AND IF REQUIRED, REPAIR THE INTERMEDIATE SHAFT/STEERING GEAR ASSEMBLY TO ASSURE THE BOLT IS FULLY SEATED AND THE SHAFT PROPERLY ASSEMBLED. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 23, 2011. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438, OR WWW.GMOWNERCENTER.COM.
HYUNDAI IS RECALLING CERTAIN MODEL YEAR 2011 SONATA VEHICLES MANUFACTURED FROM DECEMBER 11, 2009, THROUGH SEPTEMBER 10, 2010. ON SOME OF THESE VEHICLES THE STEERING COLUMN INTERMEDIATE SHAFT UNIVERSAL JOINT CONNECTIONS MAY HAVE BEEN EITHER IMPROPERLY ASSEMBLED OR INSUFFICIENTLY TIGHTENED.
Safety Risk
IMPROPER ASSEMBLY OR INSUFFICIENT TIGHTENING OF THE CONNECTIONS COULD RESULT IN A COMPLETE SEPARATION OR COMPROMISED ATTACHMENT OF THE CONNECTIONS, SUCH THAT THE DRIVER COULD EXPERIENCE A LOSS OF, OR REDUCTION IN, STEERING CAPABILITY INCREASING THE RISK OF A CRASH.
Remedy
DEALERS WILL INSPECT THE STEERING COLUMN INTERMEDIATE SHAFT UNIVERSAL JOINT CONNECTIONS FOR PROPER ASSEMBLY AND TORQUE. IN ADDITION DEALERS WILL UPDATE THE POWER STEERING SOFTWARE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 11, 2010. OWNERS MAY CONTACT HYUNDAI CUSTOMER SERVICE CENTER AT 1-787-999-3333.
HYUNDAI IS RECALLING CERTAIN MODEL YEAR 2011 SONATA VEHICLES MANUFACTURED FROM DECEMBER 11, 2009, THROUGH SEPTEMBER 10, 2010. ON SOME OF THESE VEHICLES THE STEERING COLUMN INTERMEDIATE SHAFT UNIVERSAL JOINT CONNECTIONS MAY HAVE BEEN EITHER IMPROPERLY ASSEMBLED OR INSUFFICIENTLY TIGHTENED.
Safety Risk
IMPROPER ASSEMBLY OR INSUFFICIENT TIGHTENING OF THE CONNECTIONS COULD RESULT IN A COMPLETE SEPARATION OR COMPROMISED ATTACHMENT OF THE CONNECTIONS, SUCH THAT THE DRIVER COULD EXPERIENCE A LOSS OF, OR REDUCTION IN, STEERING CAPABILITY INCREASING THE RISK OF A CRASH.
Remedy
DEALERS WILL INSPECT THE STEERING COLUMN INTERMEDIATE SHAFT UNIVERSAL JOINT CONNECTIONS FOR PROPER ASSEMBLY AND TORQUE. IN ADDITION DEALERS WILL UPDATE THE POWER STEERING SOFTWARE FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN DURING OCTOBER 2010. OWNERS MAY CONTACT HYUNDAI CUSTOMER ASSISTANCE CENTER AT 1-800-633-5151.
VOLVO IS RECALLING CERTAIN MODEL YEAR 2010-2011 C30, MODEL YEAR 2010 S40 AND V50 VEHICLES EQUIPPED WITH 6 SPEED MANUAL TRANSMISSIONS. THE GEARSHIFT LEVER STUD ASSEMBLY MAY NOT HAVE BEEN TIGHTENED TO THE CORRECT SPECIFICATION DURING ASSEMBLY. IF THE GEARSHIFT LEVER CABLE OR STUD ASSEMBLY BECOMES LOOSE, IT MAY NOT BE POSSIBLE TO ENGAGE, DISENGAGE OR SHIFT GEARS.
Safety Risk
THIS CONDITION CAN INCREASE THE RISK OF A VEHICLE CRASH.
Remedy
DEALERS WILL TORQUE THE GEARSHIFT LEVER STUD ASSEMBLY TO THE CORRECT SPECIFICATION FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 14, 2010. OWNERS MAY CONTACT VOLVO AT 1-800-458-1552 OR CUSTOMERCARE@VOLVOFORLIFE.COM .
ON CERTAIN HEAVY DUTY CLASS 8 TRUCKS EQUIPPED WITH DANA STEERING SHAFTS, THERE IS A POTENTIAL THAT THE STEERING SHAFT PINCH BOLT HOLE MAY BE INCORRECTLY LOCATED. THE PINCH BOLT FITS INTO A GROOVE IN THE STEERING GEAR INPUT SHAFT TO ENSURE THAT THE STEERING SHAFT DOES NOT SEPARATE FROM THE STEERING GEAR IF THE PINCH BOLT COMES LOOSE.
Safety Risk
THIS COULD POTENTIALLY LEAD TO STEERING SHAFT SEPARATION RESULTING IN LOSS OF CONTROL OF THE VEHICLE IF THE PINCH BOLT WERE TO COME LOOSE INCREASING THE RISK OF A CRASH.
Remedy
DEALERS WILL INSPECT THE STEERING SHAFT AND REPLACE IT AS REQUIRED FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 28, 006. OWNERS MAY CONTACT VOLVO TRUCKS AT 1-800-528-6586.
ON CERTAIN TRUCKS, THE BOLT THAT ATTACHES THE INTERMEDIATE STEERING SHAFT TO THE STEERING GEAR MAY NOT MEET SPECIFICATION. THE BOLT MAY FRACTURE RESULTING IN THE LOSS OF STEERING.
Safety Risk
IF THIS HAPPENS WHILE THE VEHICLE IS MOVING, A CRASH COULD OCCUR WITHOUT PRIOR WARNING.
Remedy
DEALERS WILL REPLACE THE INTERMEDIATE STEERING SHAFT BOLT FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 24, 2005. OWNERS MAY CONTACT GMC AT 1-866-996-9463 AND CHEVROLET AT 1-800-630-2438.
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES, IF THE INTERMEDIATE SHAFT YOKE SEPARATES FROM THE STEERING GEAR INPUT SHAFT, THE STEERING SYSTEM BECOMES DISCONNECTED.
Safety Risk
THIS COULD RESULT IN LOSS OF STEERING CONTROL, POTENTIALLY RESULTING IN A VEHICLE CRASH WITHOUT WARNING.
Remedy
DEALERS WILL INSPECT THE STEERING INTERMEDIATE SHAFT YOKE TO DETERMINE IF THE YOKE IS FULLY SEATED ON THE STEERING GEAR INPUT SHAFT. IF THE YOKE IS FULLY SEATED NO SERVICE IS REQUIRED. IF THE YOKE IS NOT FULLY SEATED AND BOLT GROOVE AND SPLINE IS VISIBLE, THE INTERMEDIATE SHAFT AND BOLT WILL BE REPLACED AS WELL AS THE BOLT AT THE STEERING COLUMN CONNECTION. OWNER NOTIFICATION BEGAN ON MAY 30, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.
VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI-VANS. THE RACK AND PINION STEERING GEARS MAY HAVE DAMAGED INPUT SHAFT BEARINGS.
Safety Risk
THIS CONDITION CAN INCREASE STEERING EFFORTS, AFFECTING STEERING CONTROL.
Remedy
DEALERS WILL INSPECT THE DATE CODE ON THE RACK AND PINION STEERING GEAR, AND, IF NECESSARY, REPLACE THOSE RACK AND PINION ASSEMBLIES THAT FALL WITHIN THE SUSPECT DATE CODE RANGE. THE DATE CODES FOR WINDSTAR MODEL VEHICLES ARE
97JB09 OR 97JC08; THE DATE CODES FOR MUSTANG MODEL VEHICLES ARE 97J09B OR
97J08B.
Also recalled in Canada